Optimization of anodic oxidation and Cu–Cr oxide catalyst preparation on structured aluminum plates processed by electro discharge machining

This paper describes the optimization of three processes applied in fabrication of a microstructured reactor for complete oxidation of volatile organic compounds. The first process involves the optimization of the electro discharge machining (EDM) method to produce a set of microchannels with a high length to diameter ratio of 100, with a standard deviation from the average diameter below 0.2%, and with a surface roughness not higher than 2.0 μm. To satisfy these criteria, fabrication of microchannels must be carried out with two machining passes in the Al51st alloy. Then, the effect of several parameters on the anodization current efficiency with respect to oxide formation was studied. The best process conditions to get a 30 μm porous alumina layer in a 0.4 M oxalic acid electrolyte, were found to be a temperature of 1 °C, an anodic current density of 5 mA/cm², and 23 h oxidation time. At last, the resulting coatings were impregnated with an aqueous solution of copper dichromate followed by drying and calcination at 450 °C to produce active catalysts. The effect of a copper dichromate concentration, number of impregnation cycles (1 or 2), and different after-treatments on catalytic activity and stability in complete oxidation of n-butane were studied. The catalytic activity of the obtained coatings is superior to that of alumina supported pelletized catalysts even at much lower loadings of active metals.     

Effect of mineral matter on coal self-heating rate

Adiabatic self-heating tests have been conducted on subbituminous coal cores from the same seam profile, which cover a mineral matter content range of 11.2-71.1%. In all cases the heat release rate does not conform to an Arrhenius kinetic model, but can best be described by a third order polynomial. Assessment of the theoretical heat sink effect of the mineral matter in each of the tests reveals that the coal is less reactive than predicted using a simple energy conservation equation. There is an additional effect of the mineral matter in these cases that cannot be explained by heat sink alone. The disseminated mineral matter in the coal is therefore inhibiting the oxidation reaction due to physicochemical effects.     

Modelling and experimental investigation of devolatilizing wood in a fluidized bed combustor

A two-dimensional model is developed for the determination of devolatilization time and char yield of cylindrical wood particles in a bubbling fluidized bed combustor. By using the concept of shape factor, the model is extended to particles of cuboid shape. The model prediction of the devolatilization time agrees with the measured data (present and those reported in the literature) for cylindrical and cuboidal shaped particles within ±20% while the char yield is predicted within ±17%. Influence of some important parameters namely, thermal diffusivity, external heat transfer coefficient and shrinkage, on the devolatilization time and char yield are studied. Thermal diffusivity shows noticeable influence on devolatilization time. The external heat transfer coefficient shows little influence beyond a value of 300 W/(m² K). However particle shrinkage shows negligible effect on the devolatilization time but has a significant influence on the char yield.     

Towards a new definition of EPOC parameters for anionic electrochemical catalysts: case of propene combustion

The electrochemical promotion of catalysis (EPOC) of propene combustion was investigated using Pt sputtered thin film on an O²⁻ conductor, 8 mol% Y₂O₃-stabilized-ZrO₂ (YSZ). In order to separate the influence of the thermal migration of the O²⁻ oxide ions from the electrolyte to the catalyst surface and the impact of an electrical polarization on the catalytic activity, several light-off experiments (cool down and heat up procedures) were successively performed under different polarizations, i.e. OCV, +2 and −2 V. These experiments have clearly shown that the presence of O²⁻ (thermally or electrochemically induced) inhibits the catalytic activity of the platinum for the propene deep oxidation. These results demonstrate the importance to define a normalized rate enhancement ratio, ρ _n , from a reference value of the catalytic rate corresponding to a Pt surface state free of O²⁻ ions.     

Impacts of varnishes and impregnation chemicals on combustion properties of oak (Quercus petreae lipsky)

This study was performed to determine the effects of varnishing after impregnation with boron compounds on combustion properties of oak. For this aim, the test samples prepared from oak (Quercus petreae Liebl.) wood were impregnated according to ASTM D 1413‐99 with boric acid (Ba) and borax (Bx) by vacuum technique. After impregnation, surfaces were coated by cellulosic (Cv), synthetic (Sn), polyurethane (Pu), waterborne (Wb), acrylic (Ac), and acid hardening (Ah) varnishes in accordance to ASTM D 3023. Combustion properties of samples after varnishing process were determined, according to ASTM E 160‐50. According to material and process types, combustion temperature was the highest in Bx and Cv, the lowest in Ba and Ac. An important difference was not observed between without flame source combustion (WFSC) and flame source combustion (FSC). According to combustion type, impregnation material and varnish type, combustion temperature was the highest value in WFSC + Bx + acid hardening varnish combination and the lowest in WFSC + Ba + acrylic varnish combination. As a result, the tested varnishes showed an increasing impact but boron compounds showed a decreasing impact on combustion properties of oak. In consequence, for usage areas having a high risk of fire, impregnation of wood material with boron compounds before varnishing will decrease combustion temperature and provide security. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

油煤浆的管道输送特性与管路设计原则

通过理论分析和管道实验，探讨了油煤浆在工业管道输送中的流变特性、流动状态和阻力特性，得出了油煤浆的物性参数、表观参数、管道阻力参数的测定值和计算公式，并在此基础上探讨了油煤浆管道输送的设计原则，为油煤浆管路的设计提供基础数据、计算方法和一般原则。     

Pulsating Jet Impingement Heat Transfer Enhancement

This article presents results from a numerical study of pulsating jet impingement heat transfer. The motivation is to seek conditions offering a significant enhancement compared to steady flow impingement drying. The CFD software package FLUENT was used for simulating slot-type pulsating jet impingement flows with confinement. The parameter study included velocity amplitude ratio, mean jet velocity, and pulsation frequency. The distance from nozzle exit to surface was three times the hydraulic diameter of the nozzle. The Reynolds number based on the nozzle hydraulic diameter and jet temperature was 2,460 with a mean jet velocity of 30 m/s, which is the base case of the numerical experiments. Results showed that time-averaged surface heat transfer increased with increasing velocity amplitude for the same mean jet velocity. Large velocity amplitudes helped enhance heat transfer by two mechanisms: high jet velocity during the positive cycle and strong recirculating flows during the negative cycle. For the cases with different mean jet velocities but the same maximum velocity, time-averaged surface heat flux decreased with decreasing mean jet velocity. As for the effects of pulsation frequency, with high-velocity amplitude ratio, time-averaged surface heat fluxes were at the same level regardless of frequency. However, at low-velocity amplitude ratio, high frequency caused stronger recirculating flows resulting in greater heat transfer compared to the cases with a lower frequency.     

Characterization of Thai limestone for desulphurization in a fluidized bed combustor

The objective of this study is to determine the chemical kinetics of desulphurization of Thai limestone in an atmospheric fluidized bed combustor (AFBC). The experiments, which employed the batch technique using the limestone samples from six major sources in Thailand, were performed in a laboratory‐scale AFBC. The results obtained were analysed and correlated in the form of apparent reaction rate and deactivation rate constants as a function of operating conditions of the furnace and their properties, respectively. The formulae derived from these correlations were kept as general as possible in order that they could be used as input parameters for the selected mathematical model of desulphurization in an AFBC that is suitable for practical use. The predicted results were in good agreement with the experimental data reported in the literature. Copyright © 2003 John Wiley & Sons, Ltd.     

Characteristic Investigation of Nano-Crystal Hydrogen Storage Alloys

A Ml (NiCoMnA1)5 hydrogen storage alloys was prepared by double-roller rapid quenching.Its microstructure, electrochemically and kinetic characteristic were studied.A uniform crystal phase with CaCu5 structure could be detected by XRD analyses, whose average grain size is 30 ～ 50 nm and the ratio of c/a of nano-crystal hydrogen storage alloy is larger.The hydrogen absorption/desertion p - C isotherms of alloy show that its fiat-performance is perfect and the magnetic stagnant effect is very little.An simulate cell is used for electrochemical measurement.Electrode is 10C, the capacity decreasing rate via the 450 cycles at 7C is less than 20%.     

Synthesis of silicon oxynitride by infiltration-mediated combustion

Silicon oxynitride Si₂N₂ O was synthesized from a mixture of Si, SiO₂, and Si₃N₄ by infiltrationmediated combustion in nitrogen gas. The chemical/phase composition of product and process parameters (temperature and burning velocity) were studied upon variation in charge composition and initial pressure of gas reagent. Parameters of the reaction yielding single-phase Si₂N₂O have been optimized.